Sony visca demo software

The file WhiteBalanceOnePush. You must place a white card in front of the camera that receives the same light as the subject and execute the command. The same thing can be done with the Sony demo software. The different options are explained on page 8 of the Sony EV-D70 manual. Upcoming Conference, we have 2 D70s this time Post by jimbo3san » Sat Aug 13, pm I have a couple of questions regarding a multi-camera 2 in our case setup: We have 2 D70s on their way this time from HQ to do different shots, etc.

They are also sending a switch and a captioning device too. My question is two parts: I want to use the control software that lpuster has created to control both. Since I don't have access to the cameras until they arrive about 2 days before the conference I am not able to "tinker" with the software the app will close if it doesn't find a camera until they arrive.

Will RS work or does it need to be the RS interface due to the distance we are planning on controlling them from the utility room where the sat.

I understand that RS is limited to 50' and RS will go ' because it is balanced voltage wise. Thanks, Jim B. Lehi, UT Jimbo3san netzero. Post by russellhltn » Sat Aug 13, pm jimbo3san wrote: What kind of control cable does this require? Have you searched the Help Center? Try doing a Google search and adding "site:churchofjesuschrist. So we can better help you, please edit your Profile to include your general location.

Post by johnshaw » Sun Aug 14, am quintonrhq wrote: A recent area training broadcast in the evening highlighted the need to adjust the white balance. Post by troywo » Sun Aug 14, pm I am not aware of training on this - I think they are saying they found the need to adjust the white balance on a broadcast they were doing. My laptop doesn't have seial port so used a usb to serial cable. My laptop found the usb to serial device but put it on com9.

I just went in and changed the port to com1. Worked great! Thanks, STeven. They show up on Ebay at times, but there not exactly cheap. Kevin Baluha from United States [2 posts]. Kevin, I think we may take you up on your offer. Is the power connector a strange cable or one that we can easily purchase?

What model is it? If you can use the contact form on the site to send us a message with your email address we can continue offline. David, If that is something you can post or place a link too I'm sure that will help.

Let me know if this helps.. I forgot to ask about S-video termination and power, were you successful in doing that? Sony power end is a little different from standard CCTV, did you manage to make it work. Thanks again. Hi Just built one of these boxes, although I have a question.

Will be using a rs to fiber converter for one camera, but the connection is a 9pin dsub. Do you have wiring diagram for rj45 to dsub for use with the box?

Thanks in advance! The D70 only has pan, tilt and zoom control. Can someone sell please me this box or tell me where I can purchase one? I need one asap! Can someone please sell me one of these boxes, or tell me where I can purchase one? Would you please repost or add them and let me know once they are online? I still 2 pairs 4,5,7,8. I have been doing a project for another set up recently, a good size budget helped , but even so the solution we ended up delivering to the client was fantastic.

So it allows a home run set up of as many as 16 cameras on the controller and will switch video on the camera selection too using ethernet connection to the router and set up in the controller was easy. Hi Ian Thanks you for posting your wiring diagram for the biscuit box.

I am in the process of building one as I am sending you this. Do you know if a serial connector in place of a rj45 on the controler lead will work and if so would you have any ides of the pin layout. Many thanks Terry. Thank you thank you thank you. I just purchased some BRC s and well I am going to make the cables with Phoenix connectors to go in and out. Still need to figure out the wire diagram for that but I will also make a box like yours for more cameras.

If you have any suggestions I am all ears. Could not get the connectors from Mouser even though everyone said the same thing. Found them on Amazon. Thank God. Have you tried siamese cables sdi with power?

I will let you know how it works out. Thanks again for all this great info. Sure, as long as you have control over the PTZ and a way to capture the video into your computer.

This is not the a vs. Is the picture flipped horizontally? After reading this article I now have these cameras! I cannot afford one of the Sony keyboards just so expensive! Does the controller I but have to support visca? Or is the rs the important bit? Where can I get that ethernet box thing you have?

From UK. RS is only the layer 2 protocol — VISCA is at a higher layer and defines the specific commands used to control the devices. Cameras were unresponsive to a power off command until we isolated communication from one line to the other via a 4PDT toggle switch I had optioned to short out with jumpers during normal operation.

Is this an explainable problem in parallel mode of RS? Helping out my church who have a RM-BR controller. I think it relates to a camera model number? But my camera is the EVI-Hs. Should that be set to on for my new camera? The cameras are serial model and the Joystick is a Serial model. I wish to connect this via a D-link through Ethernet Cat5, please advice. Do you think this will work, thanks. I have a question.

Will the second option work reliably? Depending on bitrate, can go thousands of feet. OK, great! So, I can;t seem to get an answer to this from either Sony or Panasonic. Do you think it would work well? Does your system work with my configuration. If so, do you sell your wired setup? Any suggestions? We are using RS control wiring. What happens is when I turn the knob on the BRS for exposure comp is just defaults to -7 and stays there, so then i have to go into the setup adjust back to zero and turn exposure comp off.

Hi Ian, This topic is not dead! I should be able to make it work now with almost any controller supporting VISCA on standard cat5 cabling. Biggest problem was figuring out the connections, because BRC-Z pinout is opposite to your cams.

Anybody interested in my schemes and pictures, just ask. Kind regards, Kris. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Notify me of follow-up comments by email. Notify me of new posts by email.

Update — October It blows my mind that nearly 11 years later, this is still one of the most frequently visited posts on the site… Now, back to our regularly scheduled blog post!